阳光板与钢怎么固定?

　

　　一，需求查看阳光板的胀大预留量是不是合理，板材的裁尺度是不是合格，预留的胀大空隙是不是均匀是不是满足。胀大空隙的有关数据能够找厂家供给协助。

　　二，在将PC阳光板与配件设备固定的时分，比较好将维护膜撕开30mm到50mm，这样是为了防止配件压条将维护膜压住。不过要留意的是不能揭的太多，否则容易由于设备操作划伤阳光板。

　　三，假如阳光板有UV涂层，在设备时要留意辨明，将*紫外线的一面朝外设备，没有uv涂层的一面朝内设备，切匆装错。

　　四，假如是中空阳光板设备工程，板材衔接的边缘局部至少都要坚持20mm的空间，且阳光板设备工程相互衔接的夹持配件至少要少一条筋肋 五，配件设备好，在压实密封胶条和板材的时分衔接件需求用自攻钉均匀的拧紧，不能用力过大，假如在因设备出错发作渗露，要及时用密封胶进行处理。

　　六，假如需求自行对板材进行钻钉钻孔，要考虑到PC板的热胀冷缩性能和原理，合理的留出空隙。

　　七，假如PC阳光板要进行冷弯设备，要留意冷弯的方向只能是顺着肋筋曲折，相同，为了便利凝水流出，阳光板的歪斜设备也需求顺着肋筋方向，还需求留意的是阳光板的曲折半径不能小于阳光板厚度的175倍。

　　八，查看板材设备好后还有没有渗漏，查看需求留意的环节，包含外观，质量等等。

　　九，设备过程中不能为图便利用脚践踏阳光板板面，要运用对比*业的辅助工具进行跨移。

　　十，在承认设备好PC阳光板设备和配件后，方可撕开维护膜。假如遇到施工中有要对阳光板进行维护时，也应当先撕掉，然后在覆盖上维护膜。

How to fix the sunlight plate and steel?

 1、 You need to check whether the reserved amount of expansion of the sunshine board is reasonable, whether the cutting scale of the board is qualified, and whether the reserved expansion gap is uniform and satisfied. The relevant data of swelling gap can be provided by the manufacturer for assistance.

 2、 When fixing the PC sunshine board with the accessory equipment, it is better to tear the maintenance film 30mm to 50mm, so as to prevent the accessory strip from pressing the maintenance film. However, it should be noted that it is not allowed to expose too much, otherwise it is easy to scratch the sunshine board due to equipment operation.

 3、 If the solar panel has UV coating, pay attention to distinguish when installing the equipment. Put the equipment with the UV side facing outward and the equipment without UV coating facing inward. Do not install the equipment wrongly.

 4、 If it is a hollow sunshine board equipment project, the edge part of the plate connection should adhere to a space of at least 20mm, and the clamping accessories connected with each other in the sunshine board equipment project should be at least one less rib five. The accessories and equipment are good. When compacting the sealant strip and plate, the connector needs to be tightened evenly with self tapping screws, and the force should not be too large. If there is leakage due to equipment error, It shall be treated with sealant in time.

 6、 If you need to drill nails and drill holes for the plate by yourself, you should consider the thermal expansion and cold contraction performance and principle of PC board, and leave a reasonable gap.

 7、 If the PC sunshine board needs cold bending equipment, it should be noted that the direction of cold bending can only be zigzag along the rib. Similarly, in order to facilitate the outflow of condensate, the skew equipment of the sunshine board also needs to follow the rib direction. It should also be noted that the zigzag radius of the sunshine board should not be less than 175 times the thickness of the sunshine board.

 8、 Check whether there is leakage after the plate equipment is ready, and check the links that need attention, including appearance, quality, etc.

 9、 In the process of the equipment, it is not convenient to trample on the surface of the sunshine board with your feet, but use the auxiliary tools of the comparison industry to move across.

 10、 The maintenance film can be torn off only after the PC sunshine board equipment and accessories are accepted. If it is necessary to maintain the sunshine board during construction, it should also be torn off first, and then covered with maintenance film.